This example illustrates a very simple percussion sound created with noise and usingthe sound to generate a rhythm.
The sound is created by filtering noise. The filter is controlled using the piece-wiselinear function (pwl):
(defun pulse (dur) (stretch dur (hp (noise) (pwl 0 15 0.2 6000 0.6 15000 0.75 7))))
A sequence of sounds is constructed and repeated in the following code. Notice thateach time through the pattern,
the scale factor is increased by 0.1, giving the whole sequence a crescendo:
(defun pulsepat (&optional (rep 16)) (seqrep (i rep) (stretch 0.2 (scale (* i 0.1) (seq (pulse 1) (pulse 1) (pulse 2) (pulse 2))))))(play (pulsepat 17))
This example uses the ring function from the
(play (ring 0.4 30 1.2))
These notes can be combined to create a pattern. The techno functioncreates a short pattern of 3 notes repeated any number of times:
(defun techno (rep) (seqrep (i rep) (scale 0.8 (sim (scale 0.8 (at 0.0 (ring 0.4 30 1.2))) (scale 0.6 (at 0.2 (ring 0.2 30 0.9))) (scale 0.7 (at 0.3 (ring 0.1 30 1.1))) ))))
Try this:
(play (techno 3))
The following combines and transposes rhythmic segments to create a bass line:
(play (seqrep (i 2) (seq (techno 2) (transpose 5 (techno 2)) (transpose -2 (techno 1)) (transpose 3 (techno 1)) (techno 2))))
Sounds can often be combined with time and pitch offsets to create richer textures. Thefollowing layers two sequences based on the same techno function:
(play (sim (scale 0.4 (at 0.0 (seqrep (i 2) (seq (techno 2) (transpose 5 (techno 2)) (transpose -2 (techno 1)) (transpose 3 (techno 1)) (techno 2))))) (scale 0.2 (at 0.1 (seqrep (i 2) (seq (transpose 2 (techno 2)) (transpose 7 (techno 2)) (transpose -4 (techno 1)) (transpose 5 (techno 1)) (transpose -2 (techno 2)))) ))))
Note that the second layer is almost but not exactly a transposition of the firstlayer. If it were an exact transposition, it would make sense to encapsulate the firstlayer in a function and call it twice. The following variation is much more concise, butit does not compute exactly the same sound:
(defun bass-line () (seqrep (i 2) (seq (techno 2) (transpose 5 (techno 2)) (transpose -2 (techno 1)) (transpose 3 (techno 1)) (techno 2))))
(play (sim (scale 0.4 (bass-line)) (scale 0.2 (at 0.1 (transpose 2 (bass-line))))))
This example also uses the ring function from the
(play (seqrep (i 17) (lp (scale (+ (* i 0.05 ) 0.3) (seq (transpose -4 (ring 0.1 32 0.6)) (transpose -5 (ring 0.05 20 0.2)) (transpose (* 2 i) (ring 0.1 27 0.5)) (transpose -3 (ring 0.05 22 0.1)) (transpose (* i 3) (ring 0.1 28 0.4)) (ring 0.05 31 0.7))) (* 100 i))))
This play 17 repetitions of a sound. Each time, the sound is a bit louder, the low-passfrequency is raised by 100 Hz, and two of the transpositions are increased. This creates arhythmic and evolving sound.